Product Finder

Torque Limiters SK

Bellows Couplings BK/BKL

Line Shafts ZA

Miniature Couplings MK

Elastomer / Jaw Couplings EK

Linear Couplings LK

Elastomer Couplings EK

Line Shaft Model EZV with variable length and split clamping hub

Model EZV		Series
		10		20		60		150		300		450
Type (Elastomer insert)		A	B	A	B	A	B	A	B	A	B	A	B
Rated torque (Nm)	TKN	12,5	16	17	21	60	75	160	200	325	405	530	660
Max. torque** (Nm)	TKmax	25	32	34	42	120	150	320	400	650	810	1060	1350
Inserted min. length from - to (mm)	Amin	150-2,055		200-2,075		250-2,095		300-2,115		350-2,130		400-2,150
Extended all over length from - to (mm)	Amax	190-4,000		250-4,000		310-4,000		370-4,000		440-4,000		500-4,000
Calculation (mm)	X1+X2	110		150		190		230		270		300
Outside diameter (mm)	B1	32		42		56		66.5		82		102
Outher diameter tube (mm)	B2	28		35		50		60		80		90
Outher diameter middle hub (mm)	B3	41.5		47		67		77		102		115
Outher diameter with screwhead (mm)	BS	32		44.5		57		68		85		105
Fit length (mm)	C	20		25		40		47		55		65
Inner diameter possible from Ø to Ø H7 (mm)	D1/2	5-16		8-25		14-32		19-35		19-45		24-60
Screw (ISO 4762/12.9)	E1	M4		M5		M6		M8		M10		M12
Tighting torque of the mounting screw (Nm)	E1	4		8		15		35		70		120
Screw (ISO 4762/12.9)	E2	M4		M4		M5		M6		M8		M10
Tighting torque of the mounting screw (Nm)	E2	4		4.5		8		18		35		70
Distance between centers (mm)	F1	10.5		15.5		21		24		29		38
Distance between centers (mm)	F2	15		18		26		31		41		45
Distance (mm)	G	7.5		8.5		15		17.5		20		25
Distance (mm)	O	16.6		18.6		32		37		42		52
Moment of interia (10-3 kgm2)	J1/J2	0.01		0.02		0.15		0.21		1.02		2.3
Interia of tube per meter (10-3 kgm2)	J3	0.075		0.183		0.66		1.18		2.48		10.6
Dynamic torsional stiffness of tube per meter (Nm/rad)	CTdynE	270	825	1,270	2,220	3,970	5,950	6,700	14,650	11,850	20,200	27,700	40,600
Torsional stiffness of tube per meter (Nm/rad)	CTZWR	321		1,530		6,632		11,810		20,230		65,340
Width Elastomer insert (mm)	N	26		33		49		57		67		78
Length of the couplings (mm)	H	34		46		63		73		86		99

Click here for further information regarding our elastomer inserts, including torsional stiffness and maximum possible misalignment    1 Nm = 8.85 in lbs

 

** Maximum transferable torque of the clamping hub depends on the bore diameters

Series	Ø 6	Ø 8	Ø 16	Ø 19	Ø 25	Ø 30	Ø 32	Ø 35	Ø 45	Ø 50	Ø 55	Ø 60	Ø 65	Ø 70	Ø 75	Ø 80
10	6	12	32
20		30	40	50	65
60			65	120	150	180	200
150				180	240	270	300	330
300				300	340	450	520	570	630
450						630	720	770	900	1,120	1,180	1,350
800								1,050	1,125	1,200	1,300	1,400	1,450	1,500	1,550	1,600

Higher torgue through additional keyway possible.

Function

The extended all over length and the inserted min. length are related on engineering aspects and design. Depending on the requirements, the coupling can be calculated while using the here shown two formulas to recive its min. and max. dimensions.

Extended all over length = Inserted min. length x 2 - Calculation X2

Inserted min. length = ( Extended all over length + Calculation (X1+ X2) ) / 2

Click here for information regarding the axial, angular, and lateral torsional stiffness of the EZV.

Mounting Instructions for EZV Line Shaft

After loosening the clamping screws E2, the axial moveable tube can be adjusted into the solid pipe. After reaching the axial position, the clamping bolts must be fastened under notification of the given tightening torque. The pipe of the moveable coupling part is exactly supported by the solid pipe part. A high concentricity is warranted.

 

Last update:03-12-2010